LEMON Manuals: Even more car manuals for everyone

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  Listen for an audible click when the automatic transmission shift lock control solenoid operates. Command both the ON and OFF states. Repeat the commands as necessary.
  2. 3:  Verifies that the BCM is providing voltage to the stoplamp/automatic transmission shift lock control switch.
  3. 4:  Tests if voltage is constantly being applied to the automatic transmission shift lock control solenoid.
DTC B0802

Step Action Yes No
Schematic Reference: Automatic Transmission Shift Lock Control Schematics 
Connector End View Reference: Automatic Transmission Shift Lock Control Connector End Views  or Computer/Integrating Systems Connector End Views in Computer/Integrating Systems
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2 
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, command the Brake to Shift Output ON and OFF.
Does the automatic transmission (A/T) shift lock control solenoid turn ON and OFF with each command?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems Go to Step 3 
3 
  1. Turn OFF the ignition.
  2. Disconnect the automatic transmission shift lock control switch.
  3. Turn ON the ignition, with the engine OFF.
  4. Probe the park neutral position switch park signal circuit with a test lamp connected to a good ground.
  5. With a scan tool, command the Brake to Shift Output ON and OFF.
Does the test lamp turn ON and OFF with each command?
Go to Step 4  Go to Step 5 
4 
  1. Turn OFF the ignition.
  2. Reconnect the A/T shift lock control switch.
  3. Disconnect the A/T shift lock control solenoid.
  4. Turn ON the ignition, with the engine OFF.
  5. Probe the A/T shift lock control solenoid supply voltage circuit with a test lamp connected to a good ground.
  6. With a scan tool, command the Brake to Shift Output ON and OFF.
Does the test lamp turn ON and OFF with each command?
Go to Step 7  Go to Step 6 
5 Test the park neutral position switch park signal circuit for an open or short to voltage. Refer to Circuit Testing andWiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 13  Go to Step 8 
6 Test for a open in the A/T shift lock control solenoid supply circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 13  Go to Step 9 
7 Inspect for poor connections at the harness connector of the automatic transmission shift lock control solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 13  Go to Step 10 
8 Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 13  Go to Step 12 
9
  1. Inspect for poor connections at the harness connector of the automatic transmission shift lock control switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
  2. Inspect for proper adjustment of the A/T shift lock control switch. Refer to Stop Lamp Switch Adjustment in Lighting Systems.
Did you find and correct the condition?
Go to Step 13  Go to Step 11 
10 Replace the A/T shift lock control solenoid. Refer to Automatic Transmission Shift Lock Actuator Replacement .
Did you complete the replacement?
Go to Step 13  -
11 Replace the A/T shift lock control switch. Refer to Stop Lamp Switch Replacement in Lighting Systems.
Did you complete the replacement?
Go to Step 13  -
12 Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
Did you complete the replacement?
Go to Step 13  -
13
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?
Go to Step 2  System OK