LEMON Manuals: Even more car manuals for everyone

Removal Procedure

    Fig 1: Identifying J 42640
    GM333146Courtesy of GENERAL MOTORS CORP.
    NOTE: The wheels of the vehicle must be straight ahead and the steering column in the LOCK position before disconnecting the steering column or intermediate shaft from the steering gear. Failure to do so will cause the SIR coil assembly to become uncentered, which may cause damage to the coil assembly.
  1. Lock the steering column by installing J 42640  into the underside of the steering column.
  2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure (Top Post) in Engine Electrical.
  3. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement (VIN K) in Engine Controls - 3.8L.
  4. Fig 2: Removing/Installing Range Selector Cable Bracket Bolts
    GM1385148Courtesy of GENERAL MOTORS CORP.
  5. Use a large flat-bladed tool in order to remove the range selector cable from the range selector lever.
  6. Remove the range selector cable bracket bolts (1).
  7. Remove the range selector cable bracket (2) from the transmission case and set aside.
  8. Fig 3: Disconnecting/Reconnecting Wiring Harness Retainer & Connector
    GM678825Courtesy of GENERAL MOTORS CORP.
  9. Disconnect the transaxle electrical connector C100 (2).
  10. Remove the wiring harness (3) from the wiring harness retainer (1) on the transaxle.
  11. Fig 4: Removing/Installing Ground Cable Bolt To/From Transaxle
    GM678816Courtesy of GENERAL MOTORS CORP.
  12. Remove the ground cable bolt (1) from the transaxle.
  13. Install the engine support fixture. Refer to Engine Support Fixture in Engine Mechanical - 3.8L.
  14. Fig 5: View of Transaxle To Engine Mounting
    GM160965Courtesy of GENERAL MOTORS CORP.
  15. Remove the upper engine to transaxle case bolts (2-5).
  16. Raise and Support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  17. Remove the front tire and wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  18. Fig 6: Removing/Installing Front Fascia Extensions
    GM508125Courtesy of GENERAL MOTORS CORP.
  19. Remove both of the front fascia extensions (3). Refer to Fascia Extension Replacement - Front in Bumpers.
  20. Remove the front air deflector. Refer to Air Deflector Replacement - Front in Body Front End.
  21. Fig 7: Locating Steering Rack-To-Intermediate Shaft Pinch Bolt
    GM105357Courtesy of GENERAL MOTORS CORP.
    CAUTION: Failure to disconnect the intermediate shaft from the rack and pinion steering gear stub shaft can result in damage to the steering gear or to the intermediate shaft. This damage may cause loss of steering control, which could result in an accident and possible personal injury.
  22. Remove the intermediate shaft lower pinch bolt.
  23. Disconnect the intermediate shaft from the power steering gear.
  24. Remove the power steering gear heat shield. Refer to Power Steering Gear Heat Shield Replacement in Power Steering System.
  25. Fig 8: View Of Steering Gear Mounting Bolts
    GM337379Courtesy of GENERAL MOTORS CORP.
  26. Remove the power steering gear mounting bolts.
  27. Remove the power steering line retainers from the frame.
  28. Secure the power steering gear to the exhaust manifold.
  29. Fig 9: View Of EBCM/BPMV Assembly
    GM458866Courtesy of GENERAL MOTORS CORP.
  30. Loosen the two mounting nuts (2) in order to allow removal of the brake pressure modulator valve (1) from the bracket (3).
  31. Remove the brake line retainers from the frame.
  32. Remove the left transaxle mount. Refer to Transmission Mount Replacement - Left .
  33. Remove the frame. Refer to Frame Replacement - Front in Frame and Underbody.
  34. Fig 10: Removing/Installing Front Transaxle Mount Bracket
    GM667212Courtesy of GENERAL MOTORS CORP.
  35. Remove the front transaxle mount bracket with mount attached. Refer to Transmission Mount Bracket Replacement - Front .
  36. Remove the right and left drive axles from the transaxle. Refer to Wheel Drive Shaft Replacement in Wheel Drive Shafts.
  37. Disconnect the transmission oil cooler hoses from the transaxle. Refer to Transmission Fluid Cooler Hose/Pipe Replacement .
  38. Remove the transaxle fluid filler tube. Refer to Filler Tube and Seal Replacement .
  39. Remove the torque converter cover. Refer to Torque Converter Cover Replacement .
  40. Fig 11: Locating Torque Converter Bolts
    GM166594Courtesy of GENERAL MOTORS CORP.
  41. Mark the flywheel to converter relationship to ensure proper reassembly. Remove the flywheel to torque converter bolts.
  42. Fig 12: Supporting Transaxle With A Transaxle Support Stand
    GM767120Courtesy of GENERAL MOTORS CORP.
  43. Support transaxle using an appropriate transaxle jack.
  44. Disconnect vehicle speed sensor electrical connector.
  45. Fig 13: Transaxle Brace To Transaxle Bolts
    GM732537Courtesy of GENERAL MOTORS CORP.
  46. Remove the torque strut bracket to transaxle bolts.
  47. Fig 14: Locating Strut Bracket-To-Engine Bolts
    GM732550Courtesy of GENERAL MOTORS CORP.
  48. Remove the torque strut bracket to engine bolts.
  49. Remove the torque strut bracket.
  50. Fig 15: View of Transaxle To Engine Mounting
    GM160965Courtesy of GENERAL MOTORS CORP.
  51. Remove the engine to transaxle case bolt (6) which is accessible through right wheel opening.
  52. Remove the remaining transaxle to engine bolt (1).
  53. Remove the transaxle from vehicle using an appropriate transaxle jack.
  54. Fig 16: Removing/Installing Mount Bracket To Engine
    GM667200Courtesy of GENERAL MOTORS CORP.
  55. Remove the rear transaxle bracket (1) from the transaxle.
  56. Fig 17: Removing/Installing Left Transaxle Mount & Bracket
    GM667205Courtesy of GENERAL MOTORS CORP.
  57. Remove the left transaxle bracket (1) from the transaxle.
  58. Flush the transmission cooler and lines. Refer to Automatic Transmission Oil Cooler Flushing and Flow Test (J35944-A) or Automatic Transmission Oil Cooler Flushing and Flow Test (J45096) .