LEMON Manuals: Even more car manuals for everyone

Removal Procedure

    Fig 1: Fuel Injector Sight Shield (L36)
    GM73910Courtesy of GENERAL MOTORS CORP.
  1. Remove the engine sight shield.
  2. Remove the air cleaner intake duct. Refer to Air Cleaner Intake Duct Replacement in Engine Controls - 3.8L.
  3. IMPORTANT: Remove both the throttle and the cruise control cables in order to prevent kinking of the cables during lowering of the transaxle.
    Fig 2: Cruise Control Cable At Bracket
    GM179339Courtesy of GENERAL MOTORS CORP.
  4. Remove both the throttle and the cruise control cables (1) from the throttle body and the accelerator control bracket (2).
  5. Fig 3: View of Range Selector Lever and Transaxle Wiring Harness Retainer
    GM772540Courtesy of GENERAL MOTORS CORP.
  6. Remove the range selector cable from the range selector lever.
  7. Remove the range elector cable bracket nuts.
  8. Remove the range selector cable bracket from the transmission case and set aside.
  9. Fig 4: Disconnecting/Reconnecting Wiring Harness Retainer & Connector
    GM678825Courtesy of GENERAL MOTORS CORP.
  10. Disconnect the transaxle electrical connector C100 (2).
  11. Disconnect the wiring harness (3) from the wiring harness retainer (1) on the transaxle.
  12. Remove the upper transmission case side cover bolt.
  13. Install the engine support fixture. Refer to Engine Support Fixture in Engine Mechanical - 3.8L.
  14. Raise and Support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  15. Remove the left front tire and wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  16. Fig 5: Front Fascia Extension
    GM256066Courtesy of GENERAL MOTORS CORP.
  17. Remove the left inner wheelhouse filler (2).
  18. Remove the front air deflector. Refer to Air Deflector Replacement - Front in Body Front End.
  19. Remove the left ball joint from the steering knuckle. Refer to Lower Control Arm Replacement in Front Suspension.
  20. Fig 6: View Of Steering Gear Mounting Bolts
    GM337379Courtesy of GENERAL MOTORS CORP.
  21. Remove the stabilizer bar links. Refer to Stabilizer Shaft Link Replacement in Front Suspension.
  22. Rotate the stabilizer bar to gain access to the power steering mounting bolts.
  23. Remove the power steering gear mounting bolts.
  24. Remove the power steering line retainers from the frame.
  25. Secure the power steering gear to the vehicle body.
  26. Fig 7: View Of EBCM/BPMV Assembly
    GM458866Courtesy of GENERAL MOTORS CORP.
  27. Loosen the two mounting nuts (2) in order to allow removal of the brake pressure modulator valve (1) from the bracket (3).
  28. Remove the brake line retainers from the frame.
  29. Fig 8: View Of Mount To Sub-Frame
    GM154973Courtesy of GENERAL MOTORS CORP.
  30. Remove the two lower bolts and lower nut from the rear transaxle mount (1).
  31. Fig 9: Engine Mounting
    GM667209Courtesy of GENERAL MOTORS CORP.
  32. Remove the lower nut (1) from the front transaxle mount.
  33. Support the left side of the frame with an appropriate jack.
  34. Fig 10: Identifying Frame Insulators & Frame-To-Body Guide Pin Holes
    GM105376Courtesy of GENERAL MOTORS CORP.
  35. Remove the three frame-to-body bolts (3) on the left side.
  36. IMPORTANT: DO NOT loosen the front and rear frame-to-body bolts on the right side.
  37. Loosen, but do not remove, the right center frame-to-body bolt.
  38. IMPORTANT: Insure that all pipes, hoses and wires are clear and not being bound or stressed when lowering the frame.
  39. Lower the left side of the frame.
  40. Fig 11: Left Transaxle Mount Nut
    GM768358Courtesy of GENERAL MOTORS CORP.
  41. Remove the left transaxle mount nut.
  42. Lower the vehicle enough to gain access to the engine support fixture.
  43. Using the engine support fixture, lower the transaxle.
  44. Raise the vehicle.
  45. Position an oil drain pan under the left side of the transaxle.
  46. Remove the left drive axle from the transaxle. Refer to Wheel Drive Shaft Replacement in Wheel Drive Shafts.
  47. Fig 12: Identifying Case Side Cover Bolts/Locations
    GM164786Courtesy of GENERAL MOTORS CORP.
  48. Remove the case side cover bolts.
  49. Fig 13: Identifying Case Side Cover
    GM48208Courtesy of GENERAL MOTORS CORP.
  50. Remove the case side cover (53).
  51. If replacing the side cover, remove the transmission mount bracket. Refer to Transmission Mount Bracket Replacement - Left .
  52. Clean the case and side cover gasket surfaces.