LEMON Manuals: Even more car manuals for everyone

EXPERTEC TSB (377143)

Publication date: 1993-11-08
Reference number: 377143

EXPERTEC TSB

EXPERTEC TSB

TECHNICAL SERVICE BULLETIN

Reference Number(s): 377143, Date of Issue:  11/08/93

SMU-SEC. 7A- TRANSMISSION UNIT - REPAIR, ACCUMULATOR ASSY.

Model(s): 1994 Buick Roadmaster

1994 Cadillac Fleetwood

1994 Chevrolet Caprice, Camaro, Corvette

1994 Pontiac Firebird

1994 Chevrolet AND GMC C/K, S/T Trucks and L/M, G Vans

1994 Oldsmobile Bravada

Bulletin No.: Buick 377143

Date: 11/08/1993

BULLETIN ILLUSTRATION LIST

Fig 1: Graphic
GE00W010672
Fig 2: Graphic
GE01W010672
Fig 3: Graphic
GE02W010672
Fig 4: Graphic
GE03W010672
Fig 5: Graphic
GE04W010672
Fig 6: Graphic
GE05W010672
Fig 7: Graphic
GE06W010672
Fig 8: Graphic
GE07W010672
Fig 9: Graphic
GE08W010672
Fig 10: Graphic
GE09W010672
Fig 11: Graphic
GE10W010672
Fig 12: Graphic
GE11W010672

TRANSAXLE APPLICATIONS

1994 HYDRA-MATIC 4L60-E (RPO M30)

BULLETIN COVERS

New product information for 1994 HYDRA-MATIC 4L60-E transmissions. This information has been updated since publication of the 1994 Service Manual and should be noted accordingly. Be certain to familiarize yourself with these updates to properly repair the 1994 HYDRA-MATIC 4L60-E transmission.

DATE OF PRODUCTION CHANGE

NOTE: See Fig 1 , Fig 2 & 3

Beginning with start of production 1994, HYDRA-MATIC 4L60-E transmissions were built with a new calibration that has two (2) springs in the 1-2 accumulator. The 3-4 accumulator has also changed. Some models do not use a 3-4 accumulator spring.

SERVICE MANUAL REFERENCE

Update your 1994 Service Manual with the following five (5) pages.

REMOVE OR DISCONNECT - FIGURES 9, 11 AND 12

  1. Bolt (64) and manual detent spring assembly (63).
  2. Wiring harness retaining bolts.

REMOVE OR DISCONNECT - FIGURES 11 THROUGH 14

  1. Remaining valve body bolts (62).
  2. Manual valve link (89).
  3. Control valve assembly (60).
  4. Bolts (58 and 59), accumulator cover (57), piston (56), spring (54) and spring (54A).
  5. Bolts (77) and plate (53).
  6. Spacer plate (48) and spacer plate gaskets (47 and 52).
  7. Spring (46), piston (44), and pin (43).
    • Seven checkballs are located under the valve body and one is located in the case. The large copper flash colored ball is #1 checkball (91).

VALVE BODY AND ASSOCIATED PARTS

Fig.s 105 and 107

TOOL REQUIRED

J 25025-5 Guide Pins

NOTE: The use of a honing stone, fine sandpaper or crocus cloth is not recommended for servicing stuck valves. All valve lands have sharply machined corners that are necessary for "cleaning" the bore. If these corners are rounded, foreign material could wedge between the valve and bore causing the valve to stick.

If it is found necessary to clean a valve, "micro fine" lapping compound 900 grit or finer should be used.

Too much "lapping" of a valve will cause excessive clearances and increase the chance of a valve not operating.

INSTALL OR CONNECT - FIGURES 9, 11 AND 12

  1. The wiring harness pass-thru connector into the case.
  2. The 3-4 accumulator pin (43) into the case.
  3. The 3-4 accumulator piston seal (45) onto the 3-4 accumulator piston.
  4. The 3-4 accumulator piston (44) onto the pin.
    • The end with three legs must face the valve body.
  5. The 3-4 accumulator piston spring (46).

INSTALL OR CONNECT - FIGURES 11 THROUGH 14

  1. Torque converter clutch oil screen (92).
  2. Checkball (91) into case as shown.
    • Retain with Transjel J 36850 or equivalent.
  3. J 25025-5 into the case.
  4. Screens onto spacer plate as shown.
  5. Spacer plate to case gasket (47) and spacer plate to valve body gasket (52) onto the spacer plate (48).
    • Gasket (47) identified by a "C".
    • Gasket (52) identified by a "V".
    • Retain with Transjel J 36850 or equivalent.
  6. Wiring harness (66), manual spring assembly (63), pressure switch assembly (69), dipstick stop bracket (93) and all remaining valve body bolts.
    NOTE: Torque valve body bolts in a spiral pattern starting from the center. If bolts are torqued at random, valve bores may be distorted and inhibit valve operation.
  7. TCC solenoid (66) and bolts (68).

TIGHTEN

  • Bolts to 11 N-m (8 lb. ft.)

INSTALL OR CONNECT - FIGURES 9, 11 AND 12

  • Wiring harness connections to electrical components.

To correctly hook up the wires, see the wiring diagram in the HYDRA-MATIC 4L60-E Diagnosis Section.

The pressure control solenoid (377) has two different colored connectors. The black connector should be installed on the tab farthest from the valve body.

INSTALL OR CONNECT - FIGURES 11 THROUGH 14

  1. Parking bracket (86).

    TIGHTEN

    • Bolts to 31 N,m (23 lb. ft.)
  2. The 1-2 accumulator piston seal (55) onto the 1-2 accumulator piston (56).
  3. The 1-2 accumulator piston (56) into the 1-2 accumulator cover and pin assembly (57).
    • The three legs on the piston must face toward the case when installed.
  4. The 1-2 accumulator spring (54) and 1-2 accumulator inner spring (54A) onto the piston (56).
  5. The 1-2 accumulator cover and pin assembly (57) onto the case.

    TIGHTEN

    • Torque to 11 N-m (8 lb. ft.)