LEMON Manuals: Even more car manuals for everyone

Engine Removal and Installation (2014 2015): Installation

  1. Engine Mount Bracket - Install

    1. Install the engine mount brackets and the accessory brackets, then tighten their bolts to the specified torque.

    GHH320310Courtesy of HONDA, U.S.A., INC.
  2. Engine - Install
    GHH320311Courtesy of HONDA, U.S.A., INC.
    1. Position the engine/transmission under the vehicle. Be sure that they are properly aligned. Carefully lower the vehicle until the engine/transmission are properly positioned in the engine compartment. Make sure the vehicle is not resting on any part of the engine/transmission. Support the engine/transmission with a chain hoist (A) and carefully raise the engine/transmission into place.
    NOTE: Reinstall the mounting bolts/support nuts in the sequence given in the following steps. Failure to follow this sequence may cause excessive noise and vibration, and reduce engine mount life.
  3. Upper Half of Side Engine Mount Bracket Mounting Bolt - Install
    Fig 1: Upper Half of Side Engine Mount Bracket Bolt With Torque Specifications
    GHH320312Courtesy of HONDA, U.S.A., INC.
  4. Engine Support Hanger - Install
    GHH320313Courtesy of HONDA, U.S.A., INC.
    1. Install the engine hanger balance bar. Attach the front arm (A) to the front cylinder head with a 10 mm (0.39 in) spacer (B) and a 10 x 1.25 mm bolt (C). Remove the rear arm from the engine hanger balance bar, then install the 2008 V6 attachment arm. Attach the 2008 V6 attachment arm to the rear cylinder head with a 10 mm (0.39 in) spacer (D) and an 8 x 1.25 mm bolt (E).

    2. Install the engine support hanger onto the vehicle as shown, and attach the hook to the slotted hole in the engine hanger balance bar. Tighten the wing nut (F) by hand, and lift and support the engine/transmission.

    NOTE: AAR-T1256 two sets required for stacking additional cross section bars.
  5. Chain Hoist - Remove
  6. Battery Base - Install
    Fig 2: Battery Base and Harness With Torque Specifications
    GHH320314Courtesy of HONDA, U.S.A., INC.
    1. Install the battery base and the harness clamps (A).
  7. Vehicle - Lift
    1. Raise the vehicle.
  8. Front Subframe - Support
    GHH320315Courtesy of HONDA, U.S.A., INC.
    1. Attach the subframe adapter to the front subframe by looping the belt (A) over the front of the front subframe, then secure the belt with its stop (B), and tighten the wing nut (C).

    2. Install the subframe adapter with the front subframe on the transmission jack base using four bolts, then raise the front subframe up to the body.

  9. Front Subframe - Install - Refer to: Subframe Removal and Installation (2014 2015)
    NOTE: Align the front subframe with the subframe alignment pin.
  10. Transmission Mount Mounting Bolt - Tighten
    Fig 3: Transmission Mount Bolts With Torque Specifications
    GHH320316Courtesy of HONDA, U.S.A., INC.
  11. Transmission Ground Cable - Connect
    Fig 4: Transmission Ground Cable With Torque Specifications
    GHH320317Courtesy of HONDA, U.S.A., INC.
  12. EPS Connector Wire Harness - Insert
    GHH320318Courtesy of HONDA, U.S.A., INC.
    1. Insert the EPS connector wire harness.

    2. Install the harness grommet (A) and the harness clamp (B).

  13. Front Engine Mount Actuator Connector - Connect
    GHH320319Courtesy of HONDA, U.S.A., INC.
    1. Install the harness clamp (A).

    2. Connect the connector (B).

  14. Vehicle - Lift
    1. Lower the vehicle.
  15. Engine Support Hanger, Engine Hanger Balance Bar, and Engine Hanger Adapter Set - Remove
    NOTE: After removing the engine hanger adapters, install the service caps.
  16. Front Engine Mount and Front Engine Mount Stop Mounting Bolt - Install
    Fig 5: Front Engine Mount and Front Engine Mount Stop With Torque Specifications
    GHH320320Courtesy of HONDA, U.S.A., INC.
  17. No. 6 Cylinder Ignition Coil - Install
  18. Rear Engine Mount and Rear Engine Mount Stop Mounting Bolt - Install
    Fig 6: Rear Engine Mount and Rear Engine Mount Stop With Torque Specifications
    GHH320321Courtesy of HONDA, U.S.A., INC.
  19. Upper half of Side Engine Mount Bracket Mounting Bolt - Retighten
    Fig 7: Upper half of Side Engine Mount Bracket Mounting Bolt - Retighten Torque Specifications
    GHH320322Courtesy of HONDA, U.S.A., INC.
    1. Loosen the mounting bolts for the upper half of the side engine mount bracket, then retighten them in the numbered sequence shown.
  20. Harness Bracket - Install
    Fig 8: Harness Bracket With Torque Specifications
    GHH320323Courtesy of HONDA, U.S.A., INC.
    1. Install the harness bracket (A) to the rear cylinder head.
  21. Connector Bracket - Install
    Fig 9: Connector Bracket Bolt With Torque Specifications
    GHH320324Courtesy of HONDA, U.S.A., INC.
    1. Install the connector bracket (A) to the front cylinder head.
  22. Positive Alternator Cable - Connect
    GHH320325Courtesy of HONDA, U.S.A., INC.
    1. Connect the positive alternator cable (A) and the connector (B).

    2. Install the harness clamp (C).

  23. Positive Starter Cable - Connect
    GHH320326Courtesy of HONDA, U.S.A., INC.
    1. Connect the positive starter cable (A).

    2. Install the harness clamp (B).

  24. Front Bulkhead - Remove
  25. A/C Compressor - Install
    Fig 10: A/C Compressor With Torque Specifications
    GHH320327Courtesy of HONDA, U.S.A., INC.
  26. Right Front Bulkhead Brace - Install
  27. Alternator - Install
  28. Radiator - Install
  29. Radiator Fan Shroud and A/C Condenser Fan Shroud - Install
  30. Heater Hose - Connect
    GHH320328Courtesy of HONDA, U.S.A., INC.
    1. Connect the heater hoses (A).
  31. Harness Holder - Install
    GHH320329Courtesy of HONDA, U.S.A., INC.
    1. Install the harness holders (A).
  32. Vehicle - Lift
    1. Raise the vehicle.
  33. Front Driveshaft - Install - Refer to: Front Driveshaft Removal and Installation (2014 2015)
  34. Tie-Rod End Ball Joint - Connect
  35. Stabilizer Link Ball Joint - Connect
  36. Lower Arm Ball Joint - Connect
  37. Front Suspension Stroke Sensor Connector - Connect (With Headlight Leveling System)
    GHH320330Courtesy of HONDA, U.S.A., INC.
    1. Install the front suspension stroke sensor mounting nut.

    2. Connect the front suspension stroke sensor connector (A).

    3. Install the harness clamps (B).

  38. Transfer Assembly - Install (AWD) - Refer to: Transfer Assembly Removal and Installation (2014 2015),
  39. Propeller Shaft - Install (AWD)
  40. Under-Floor TWC - Install - Refer to: Warm Up TWC Removal and Installation,  or Under-Floor TWC Removal and Installation 
  41. Secondary HO2S Connector - Connect 
  42. Front Inner Fender - Install - Refer to: Front Inner Fender Removal and Installation, or Rear Inner Fender Removal and Installation
  43. Splash Shield - Install
  44. Front Wheel - Install - Refer to: Wheel Removal and Installation (2014 2015 2016)
  45. Vehicle - Lift
    1. Lower the vehicle.
  46. EPS Connector - Connect (Cabin Side)
    GHH320331Courtesy of HONDA, U.S.A., INC.
    1. Connect the EPS connectors (A).

    2. Install the passenger's center console side cover

    .

  47. Steering Joint - Connect
  48. Shift Cable - Connect (Transmission Side)
  49. Brake Booster Vacuum Hose - Connect
    GHH320332Courtesy of HONDA, U.S.A., INC.
    1. Connect the brake booster vacuum hose (A).
  50. EVAP Canister Purge Joint - Install
    GHH320333Courtesy of HONDA, U.S.A., INC.
    1. Install the EVAP canister purge joint.

    2. Connect the EVAP canister purge hose (A).

  51. Fuel Feed Hose - Connect (High Pressure Fuel Pump Side)
  52. PCM Connector and Engine Wire Harness Connector - Connect
    GHH320334Courtesy of HONDA, U.S.A., INC.
    1. Install the harness clamp (A).

    2. Connect the connectors (B).

  53. Intake Air Duct - Install
    GHH320335Courtesy of HONDA, U.S.A., INC.
    1. Install the intake air duct.

    2. Connect the breather pipe (A).

  54. Air Cleaner - Install 
  55. Battery - Install - Refer to: Battery Removal and Installation (2014 2015)
  56. Air Intake Tube - Install 
  57. Fuel Leak - Inspect
    1. Turn the vehicle to the ON mode, but do not operate the starter. After the fuel pump runs for about 2 seconds, the fuel rail will be pressurized. Repeat this two or three times, then check for fuel leakage.
  58. Engine Oil - Refill
  59. ATF - Refill - Refer to: ATF Replacement (2014 2015)
  60. Transmission Gear - Check
    1. Move the shift lever to each gear, and verify that the A/T gear position indicator follows the transmission range switch.
  61. Engine Coolant - Refill/Air Bleed
  62. Fluid Leak - Check
  63. PCM - Reset
  64. CKP Pattern - Clear/Learn
  65. Idle Speed - Inspect
  66. Ignition Timing - Inspect
  67. Front Bulkhead Cover - Install
  68. Engine Cover - Install
  69. Hood Support Strut - Install
    1. Remove the hood prop bar.

    2. Install the hood support strut - Refer to: Hood Support Strut Removal and Installation (2014 2015 2016)

    .

  70. Wheel Alignment - Check - Refer to: Wheel Alignment (2014 2015 2016)
  71. Steering Angle Sensor Neutral Position - Clear
  72. Headlight Initial Position - Learn (With Headlight Leveling System)