LEMON Manuals: Even more car manuals for everyone

Moonroof Control Unit Input Test

NOTE: If the moonroof works OK manually, but will not work in AUTO, or reverses frequently (obstacle detection), do the moonroof calibration (see RESETTING THE MOONROOF CONTROL UNIT  ) before proceeding with the input test.
  1. Turn the ignition switch OFF.
  2. Remove the headliner (see HEADLINER REMOVAL/INSTALLATION ).
  3. Disconnect the 10P connector (A) from the moonroof control unit (B).
    Fig 1: Identifying Moonroof Control Unit 10P Connector
    G06268864Courtesy of AMERICAN HONDA MOTOR CO., INC.
  4. Inspect the connector and socket terminals to be sure they are all making good contact.
    • If the terminals are bent, loose or corroded, repair them as necessary, and recheck the system.
    • If the terminals look OK, go to step 5.
  5. Reconnect the connector to the moonroof control unit, and make these input tests at the connector.
    • If any test indicates a problem, find and correct the cause, then recheck the system.
    • If all the input tests prove OK, go to step 6.
      TEST CONDITION CHART

      Cavity Wire Test condition Test: Desired result Possible cause if result is not obtained
      1 GRN Under all conditions Check for voltage to ground:
      There should be battery voltage.
      • Blown No. 24 (20 A) fuse in the under-dash fuse/relay box
      • An open in the wire
      5 PUR Ignition switch ON (ID Check for voltage to ground:
      There should be battery voltage.
      • Blown No. 32 (20 A) fuse in the under-dash fuse/relay box
      • An open in the wire
      10 BLK Under all conditions Check for voltage to ground:
      There should be less than 0.5 V.
      • Poor ground (G503)
      • An open in the wire
      6 WHT Moonroof switch in AUTO OPEN or AUTO CLOSE position Check for voltage to ground at the No. 5 and No. 6 terminals:
      There should be battery voltage.
      • Faulty moonroof switch
      • Blown No. 32 (20 A) fuse in the under-dash fuse/relay box (1)
      • Blown No. 23 (10 A) fuse in the under-hood fuse/relay box (2)
      • An open in the wire
      7 LT GRN Moonroof switch in TILT position Check for voltage to ground at the No. 5 and No. 7 terminals:
      There should be battery voltage.
      • Faulty moonroof switch
      • Blown No. 32 (20 A) fuse in the under-dash fuse/relay box (1)
      • Blown No. 23 (10 A) fuse in the under-hood fuse/relay box (2)
      • An open in the wire
      8 YEL Moonroof switch in CLOSE position Check for voltage to ground at the No. 5 and No. 8 terminals:
      There should be battery voltage.
      • Faulty moonroof switch
      • Blown No. 32 (20 A) fuse in the under-dash fuse/relay box (1)
      • Blown No. 23 (10 A) fuse in the under-hood fuse/relay box (2)
      • An open in the wire
      9 LT BLU Moonroof switch in OPEN position Check for voltage to ground at the No. 5 and No. 9 terminals:
      There should be battery voltage.
      • Faulty moonroof switch
      • Blown No. 32 (20 A) fuse in the under-dash fuse/relay box (1)
      • Blown No. 23 (10 A) fuse in the under-hood fuse/relay box (2)
      • An open in the wire
      (1) '06-07 models
      (2) '08-09 models
  6. Check the ECM/PCM DTCs. If there is no DTC, jump the SCS line with the HDS, then disconnect the ECM/PCM connector A (44P), and the moonroof control unit/motor 10P connector.
  7. Make these input tests at the connector.
    • If any test indicates a problem, find and correct the cause, then recheck the system.
    • If all the input tests prove OK, the control unit must be faulty; replace the moonroof control unit/motor.
      TEST CONDITION CHART

      Cavity Wire Test condition Test: Desired result Possible cause if result is not obtained
      4 BLU Under all conditions Check for continuity between the No. 4 terminal and ECM/ PCM connector A (44P) No. 29 terminal:
      There should be continuity.
      An open in the wire
      Check for continuity between the No. 4 terminal and body ground:
      There should be no continuity.
      A short to ground in the wire