LEMON Manuals: Even more car manuals for everyone

DTC 2707: MIC Diag

WARNING: This page is about a different car, the 2011 Acura TL, 2010 Acura TL, and 2009 Acura TL. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
  1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode, then back to ON (II), or the ON mode
  2. Go into the Diagnostic Menu, and select the Self-Diagnosis Mode in the Select Diagnosis items menu (see SYSTEM DIAGNOSTIC MODE )
  3. Select the System Links

    Is the Mic icon red? 

    YES  -Go to step 4

    NO  -Go to step  9

  4. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode
  5. Check for poor connections or loose terminals at these items
    • Audio-navigation unit connector H (28P)
    • HandsFreeLink control unit 28P connector
    • HFL-navigation microphone 7P connector

    Are the connections OK? 

    YES  -Go to step 6

    NO  -Repair poor connections or loose terminals

  6. Connect the HDS to the DLC (see GENERAL TROUBLESHOOTING INFORMATION )
  7. Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode
  8. Check for DTCs with the HDS

    Is DTC B1775 or B1776 indicated? 

    YES  -Troubleshoot the indicated DTC

    NO  -Go to step  11

  9. Select the Mic in the System Links
  10. Press the TALK button on the steering wheel switch, then check the Mic Level (see MIC LEVEL )

    Is the microphone level OK? 

    YES  -Intermittent failure, the system is OK at this time

    NO  -Replace the HFL-navigation microphone (see HFL-NAVIGATION MICROPHONE REMOVAL/INSTALLATION )

  11. Measure the voltage between body ground and HFL-navigation microphone 7P connector terminals No 6 and No 7 individually
    Fig 1: Measuring Voltage Between HFL-Navigation Microphone 7P Connector Terminals No 6 And No 7 Body Ground
    G05989813Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    YES  -Go to step 12

    NO  -Repair open in the wire(s)

  12. Measure the voltage between HFL-navigation microphone 7P connector terminal No 1 and body ground
    Fig 2: Measuring Voltage Between HFL-Navigation Microphone 7P Connector Terminal No 1 And Body Ground
    G05989814Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there less than 0.2V? 

    YES  -Go to step 13

    NO  -Repair open or high resistance in the wire between audio-navigation unit and body ground to G401 (see DASHBOARD WIRE HARNESS (VIEW OF DRIVER'S SIDE) )

  13. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode
  14. Disconnect the HFL-navigation microphone 7P connector
  15. Check for continuity between the terminals of the HandsFreeLink control unit 28P connector according to the table
    CONTINUITY REFERENCE CHART

    From terminal To terminals
    12 (GRY) 13 (PNK), 14 (BLU)
    Fig 3: Identifying Handsfreelink Control Unit 28P Connector
    G05989815Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity between any of the terminals? 

    YES  -There is a short in the wires between the HandsFreeLink control unit and the audio-navigation unit. Replace the affected shielded harness.

    NO  -Replace the HFL-navigation microphone (see HFL-NAVIGATION MICROPHONE REMOVAL/INSTALLATION ).